- Specialty Nylon Solutions
- Custom Engineered Thermoplastics
Technical Data Sheet
NYLENE USA
1421 Hwy 136 West
Henderson, Kentucky 42420
| Phone: | 270-826-7641 |
| Toll-free: | 800-626-7050 |
NYLENE CANADA ULC.
200 McNab Street
Arnprior, Ontario K7S 3P2
| Phone: | 613-623-3191 |
| Toll-free: | 800-267-7394 |
ISO/IEC 17025 & ISO 9001:2015 Accredited Facilities
Product is manufactured in Wayne, NJ, Henderson, KY
Web: www.nylene.com | Email: info@nylene.com
TDS Ref ID: 1250
This information was updated on January 9, 2024
| Resin Type: |
|
| Description: |
|
| Properties | ASTM/ISO Procedure | Unit | English | SI | |
|---|---|---|---|---|---|
| Physical | |||||
| Specific Gravity | ISO 1183 | n/a | 1.09 | 1.09 | |
| Mechanical | |||||
| Tensile Strength | ISO 527 | psi (MPa) | 7,832 | 54 | |
| Flexural Modulus | ISO 178 | psi (MPa) | 261,000 | 1,800 | |
| Elongation | ISO 527 | % | 4 | ||
| Notched Izod @ 23°C | ISO 180 | ft-lb/in² (kJ/m²) | 0.1 | 8 | |
| Notched Izod @ -40°C | ISO 180 | ft-lb/in² (kJ/m²) | 0.1 | 5 | |
| Thermal | |||||
| DTUL @ 264 psi/1.82 MPa | D648 | °F (°C) | 113 | 45 | |
| Melt Point | ISO 11357 | °F (°C) | 421 | 216 | |
| Notes: | Testing conducted on dry-as-molded specimens at 73°F (22.8°C} |
| Zone | °F (C°) |
|---|---|
| Feed | 420-440 (216-227) |
| Transition | 440-460 (227-238) |
| Metering | 450-470 (232-243) |
| Die | 450-470 (232-243) |
| Melt Temp. | 450-470 (232-243) |
| Line Rate | pph-rpm |
|---|---|
| 21/2" extruder | 1.5-1.9 |
| 31/2" extruder | 3.5-4.5 |
| 41/2" extruder | 6.5-7.5 |
Residence Time: Screw should not be left idle for more than 3-4 minutes with melt in the barrel. Excess residence will be visible as black carbon specs in the melt.
Regrind Level: Typically, up to 25% is recommended but higher levels are possible with little or no effect on flow and finish.
Drying Temperature: Although Nylene resins are packaged and delivered in a low moisture state, it is good material handling practice to use a hopper dryer to maintain dryness. Should pre-drying be necessary, use settings of 180 °F (82.2°C) air at dew point of -40 at a rate of 1 cu. ft. / hour per pound of resin and a residence time of 2-4 hours.
Cooling and Sizing: While both air and water can be used as the cooling medium, air is preferred. The use of air allows additional time for sizing and reduces residual stress. This aids in reducing warpage, especially in profiles with varying wall sections. If water is used, heat the first section to above 100 °F (38°C) to reduce quenching and residual stress.
Die Design: Draw down of 30% is typical for all dimensions except wall thickness.
Land length: should be around 10x wall thickness.
Fillers/Reinforcements:
Approvals & Recognition:
Automotive OEM: Specs & Colors:
Automotive Colors:
Disclaimer
Nylene USA and Nylene Canada ULC are subsidiaries of the Polymeric Resources Corporation (PRC). Nylene companies develop and manufacture specialty nylons and engineering thermoplastics.
Nylene USA
|
|
|---|---|
| Corporate HQ/Facility | |
| Kentucky Facility | |
Nylene Canada
|
|
|---|---|
| Ontario Facility | |
| Canada Sales Office |
International
|
|
|---|---|
| South America | |
| China | |
| Malaysia | |
| Europe/Middle East |
