- Specialty Nylon Solutions
- Custom Engineered Thermoplastics
Technical Data Sheet
NYLENE USA
1421 Hwy 136 West
Henderson, Kentucky 42420
| Phone: | 270-826-7641 |
| Toll-free: | 800-626-7050 |
NYLENE CANADA ULC.
200 McNab Street
Arnprior, Ontario K7S 3P2
| Phone: | 613-623-3191 |
| Toll-free: | 800-267-7394 |
ISO/IEC 17025 & ISO 9001:2015 Accredited Facilities
Product is manufactured in Wayne, NJ
Web: www.nylene.com | Email: info@nylene.com
TDS Ref ID: 1296
This information was updated on December 12, 2023
| Resin Type: |
|
| Description: |
|
| Properties | ASTM/ISO Procedure | Unit | English | SI | |
|---|---|---|---|---|---|
| Physical | |||||
| Specific Gravity | D792 | n/a | 1.44 | 1.44 | |
| Mold Shrinkage | D955 | mm/mm | 0.002 | ||
| Mechanical | |||||
| Tensile Strength | D638 | psi (MPa) | 23,900 | 165 | |
| Tensile Modulus | D638 | psi (MPa) | 1,651,000 | 11,400 | |
| Flexural Modulus | D790 | psi (MPa) | 1,310,000 | 9,030 | |
| Elongation @ Break | D638 | % | 3 | ||
| Notched Izod @ 23°C | D256 | ft-lb/in (J/m) | 2 | 105 | |
| Thermal | |||||
| DTUL @ 264 psi/1.82 MPa | D648 | °F (°C) | 403 | 206 | |
| Melt Point | D3418 | °F (°C) | 420 | 215 | |
| Notes: | Testing conducted on dry-as-molded specimens at 73°F (22.8°C} |
| Pressure | psi |
|---|---|
| Injection | 8-18,000 |
| Hold | 6-15,000 |
| Back | 0-50 |
Melt Temperature: Nylene PA6 melts at 428°F, (220°C) actual melt temperatures of 440-560°F (227-293°C) are permissible, depending on residence time and shot size.
Mold Temperature: 120-200°F (49-93°C), highly filled grades require 180-200°F (82-93°C) to obtain the best overall surface appearance, higher temperatures will increase crystallinity.
Residence Time: should not exceed 6 minutes if possible, less with higher melt temperatures.
Shot Size: should be between 25-75% of barrel capacity.
Fill Rate: fast fill rates are suggested for best surface appearance.
Regrind Level: typically no more than 25% is recommended, with higher levels possible for unfilled grades depending on the end use requirements. Make certain regrind is properly dried to virgin moisture levels.
Drying Temperature: 150-180°F (66-82°C) for 2-4 hours, Nylene PA6 should be dried to less than 0.20% moisture for optimum performance. Drying longer than 4 hours or at higher temperatures may cause discoloration of the polymer or adversely affect important physical properties.
Fillers/Reinforcements:
Approvals & Recognition:
Automotive Colors:
Disclaimer
Nylene USA and Nylene Canada ULC are subsidiaries of the Polymeric Resources Corporation (PRC). Nylene companies develop and manufacture specialty nylons and engineering thermoplastics.
Nylene USA
|
|
|---|---|
| Corporate HQ/Facility | |
| Kentucky Facility | |
Nylene Canada
|
|
|---|---|
| Ontario Facility | |
| Canada Sales Office |
International
|
|
|---|---|
| South America | |
| China | |
| Malaysia | |
| Europe/Middle East |
