Nylene 609

Technical Data Sheet

NYLENE USA

1421 Hwy 136 West

Henderson, Kentucky 42420

Phone:270-826-7641
Toll-free:800-626-7050

NYLENE CANADA ULC.

200 McNab Street

Arnprior, Ontario K7S 3P2

Phone:613-623-3191
Toll-free:800-267-7394

ISO/IEC 17025 & ISO 9001:2015 Accredited Facilities

Product is manufactured in  Henderson, KY

Web: www.nylene.com  | Email: info@nylene.com

TDS Ref ID: 1520

  • Nylene® 609
  • Technical Data Sheet
Resin Type:
  • Nylon 6
Description:
  • Nylon 6, high viscosity, extrusion grade recommended for practically all types of extrusion including profile, film, and extrusion coating
  • Can also be used for blow molding applications
  • Optimum processing conditions should permit for a melt temperature of 550 - 575°F (289 - 301°C) at the die.
  • Especially recommended for flexible packaging where as a film or coating it is used for the outside layer in multi-ply film constructions
Properties ASTM/ISO Procedure Unit English SI
Physical
Specific Gravity D792 n/a 1.12 1.12
Relative Viscosity D789 Formic Acid n/a 200
Water Absorption D570 % 1.7
Mechanical
Elongation D638 (77°C) % 140
Flexural Modulus D790 psi (MPa) 380,000 2,620
Flexural Stiffness D790 psi (MPa) 260,000 1,793
Notched Izod @ 23°C D256 ft-lb/in (J/m) 1 53
Rockwell Hardness R Scale - 118
Tensile Strength D638 psi (MPa) 11,000 76
Thermal
Heat Deflection @ 264 psi (1.8 MPa) D648 °F (°C) 60 140
Melt Point D3418 °F (°C) 430 221
Notes: Testing conducted on dry-as-molded specimens at 73°F (22.8°C}

Recommended Processing Considerations: High Viscosity Extrusion

Zone°F (C°)
Feed420-445 (216-229)
Transition435-465 (224-241)
Metering445-475 (229-246)
Die
445-475 (229-246)
Melt Temp.
455-489 (235-254)
Line Ratepph-rpm
21/2" extruder1.5-1.9
31/2" extruder3.5-4.5
41/2" extruder6.5-7.5

Residence Time: Screw should not be left idle for more than 3-4 minutes with melt in the barrel. Excess residence will be visible as black carbon specs in the melt.

Regrind Level: Typically, up to 25% is recommended but higher levels are possible with little or no effect on flow and finish.

Drying Temperature: Although Nylene resins are packaged and delivered in a low moisture state, it is good material handling practice to use a hopper dryer to maintain dryness. Should pre-drying be necessary, use settings of 180 °F (82.2°C) air at dew point of -40 at a rate of 1 cu. ft. / hour per pound of resin and a residence time of 2-4 hours.

Cooling and Sizing: While both air and water can be used as the cooling medium, air is preferred. The use of air allows additional time for sizing and reduces residual stress. This aids in reducing warpage, especially in profiles with varying wall sections. If water is used, heat the first section to above 100 °F (38°C) to reduce quenching and residual stress.

Die Design: Draw down of 30% is typical for all dimensions except wall thickness.

Land length: should be around 10x wall thickness.

Fillers/Reinforcements:

    Approvals & Recognition:

    • Direct Food Contact: FDA 21 CFR 177.1500

    Automotive OEM: Specs & Colors:

    • Chrysler, Fiat, Peugeot, FCA Group
      MS-DB41 CPN 5165

    Automotive Colors:

    Disclaimer

    Nylene does not guarantee the accuracy of this information or the suitability of this product for any given application or usage situation. These values are based on test specimens and should not be used to establish specification limits or fabricate tooling.

    Product Inquiry

    Quote Request

    Please provide your contact information and your requirements for a Quote or Sample. Alternatively, you can call us at 1-800-626-7050.

    Sample Request

    Please provide us with your requirements or any information on the material you would like to replace. To speak to a representative about your application, please call 1-800-626-7050.

    Product Stewardship & Safety Data Sheet Request

    Please fill out the form below to request safety, compliance, approvals, and certification documents. This will ensure that we provide you with the information that meets your needs and conforms to regional legislation requirements. We send up-to-date SDS via email.

    Contact Sales & Technical Service
    You may also call US: 1-800-626-7050 (Canada: 1-800-267-7394 x200) for media inquiries.
    Skip to content