Technical Data Sheet

Preparing your data sheet file...

Please check your downloads after the page refreshes.

Preparing your data sheet file...

Please check your downloads after the page refreshes.

NYLENE USA

1421 Hwy 136 West

Henderson, Kentucky 42420

Phone:270-826-7641
Toll-free:800-626-7050

NYLENE CANADA ULC.

200 McNab Street

Arnprior, Ontario K7S 3P2

Phone:613-623-3191
Toll-free:800-267-7394

ISO/IEC 17025 & ISO 9001:2015 Accredited Facilities

Product is manufactured in  Henderson, KY

Web: www.nylene.com  | Email: info@nylene.com

TDS Ref ID: 1586

  • Nylene® 6250L
  • Technical Data Sheet
Resin Type:
  • Nylon 6/12
Description:
Nylene 6250L is a low viscosity nylon 6/12 molding resin.  This material us used in applications requiring  good electrical insulation properties.  When molding, Nylene 6250L has high flow characteristics at minimum temperatures.
Properties ASTM/ISO Procedure Unit English SI
Physical
Relative Viscosity ISO 307 Sulfuric Acid n/a 2.4
Mechanical
Elongation @ Break D638 % 250
Tensile Strength @ Yield D638 psi (MPa) 9427 65
Physical
Density ISO 1183 lb/in³ (g/cm³) 0.0376 1
Thermal
Melt Point (DSC) ASTM D3418 °F (°C) 423 217
Mechanical
Flexural Modulus D790 psi (MPa) 290000 2,000
Notes: Testing conducted on dry-as-molded specimens at 73°F (22.8°C}

Recommended Processing Considerations: PA 6/12 Specialty Nylon

Pressure psi
Injection 4 – 12,000
Hold 3 – 9,000
Back 0 – 50


Maximum Moisture:
0.2%

Mold Temperature:
150-250 °F, highly filled grades require >175 °F to obtain the best overall surface appearance

Residence Time:
Should not exceed 6 minutes, less with higher melt temps.

Shot Size:
Should be between 25-75% of barrel capacity.

Fill Rate:
Fast fill rates are suggested for best surface appearance.

Regrind Level:
Typically no more than 25% is recommended, with higher levels possible for unfilled grades depending on the end use requirements. Make certain regrind is properly dried to virgin moisture levels.

Drying Temp.
Nylene 6/12 – 150-180 °F for 2-4 hours

jeff.johnson@nylene.com

Fillers/Reinforcements:

    Approvals & Recognition:

      Automotive Colors:

      Disclaimer

      Nylene does not guarantee the accuracy of this information or the suitability of this product for any given application or usage situation. These values are based on test specimens and should not be used to establish specification limits or fabricate tooling.

      Call Us

      Nylene USA 800-626-7050
      Nylene Canada 800-267-7394
      Corporate Office 973-694-3549

      Product Inquiry

      Quote Request

      Please provide your contact information and your requirements for a Quote or Sample. Alternatively, you can call us at 1-800-626-7050.

      Sample Request

      Please provide us with your requirements or any information on the material you would like to replace. To speak to a representative about your application, please call 1-800-626-7050.

      Product Stewardship & Safety Data Sheet Request

      Please fill out the form below to request safety, compliance, approvals, and certification documents. This will ensure that we provide you with the information that meets your needs and conforms to regional legislation requirements. We send up-to-date SDS via email.

      Contact Sales & Technical Service
      You may also call US: 1-800-626-7050 (Canada: 1-800-267-7394 x200) for media inquiries.