- Specialty Nylon Solutions
- Custom Engineered Thermoplastics
Technical Data Sheet
NYLENE USA
1421 Hwy 136 West
Henderson, Kentucky 42420
| Phone: | 270-826-7641 |
| Toll-free: | 800-626-7050 |
NYLENE CANADA ULC.
200 McNab Street
Arnprior, Ontario K7S 3P2
| Phone: | 613-623-3191 |
| Toll-free: | 800-267-7394 |
ISO/IEC 17025 & ISO 9001:2015 Accredited Facilities
Product is manufactured in Wayne, NJ
Web: www.nylene.com | Email: info@nylene.com
TDS Ref ID: 1431
This information was updated on February 22, 2024
| Resin Type: |
|
| Description: |
|
| Properties | ASTM/ISO Procedure | Unit | English | SI | |
|---|---|---|---|---|---|
| Physical | |||||
| Specific Gravity | D792 | n/a | 1.20 | 1.20 | |
| Mechanical | |||||
| Tensile Strength | D638 | psi (MPa) | 11,500 | 79 | |
| Flexural Modulus | D790 | psi (MPa) | 415,000 | 2,860 | |
| Elongation | D638 | % | 20 | ||
| Notched Izod @ 23°C | D256 | ft-lb/in (J/m) | 1 | 53 | |
| Thermal | |||||
| DTUL @ 264 psi/1.82 MPa | D648 | °F (°C) | 194 | 90 | |
| Melt Point | D3418 | °F (°C) | 490 | 254 | |
| Notes: | Testing conducted on dry-as-molded specimens at 73°F (22.8°C} |
| Pressure | psi |
|---|---|
| Injection | 7-15,000 |
| Hold | 5-12,000 |
| Back | 0-50 |
Melt Temperature: Nylene® PA6/6 melts at 490 °F (254°C), actual melt temperatures of 540-600 (282-316°C) are permissible, depending on residence time and shot size.
Mold Temperature: 120-200 °F (49-93°C), highly filled grades require 180-200 °F (82-93°C) to obtain the best overall surface appearance, higher temperatures will increase crystallinity.
Residence Time: should not exceed 6 minutes if possible, less with higher melt temperatures.
Shot Size: should be between 25-75% of barrel capacity.
Fill Rate: fast fill rates are suggested for best surface appearance.
Regrind Level: typically no more than 25% is recommended, with higher levels possible for unfilled grades depending on the end use requirements. Make certain regrind is properly dried to virgin moisture levels.
Drying Temperature: 150-180 °F (65-182°C)(for 2-4 hours, Nylene® PA6/6 should be dried to less then 0.20% moisture for optimum performance. Drying longer than 4 hours or at higher temperatures may cause oxidation of the polymer or remove essential volatiles.
Fillers/Reinforcements:
Approvals & Recognition:
Automotive Colors:
Disclaimer
Nylene USA and Nylene Canada ULC are subsidiaries of the Polymeric Resources Corporation (PRC). Nylene companies develop and manufacture specialty nylons and engineering thermoplastics.
Nylene USA
|
|
|---|---|
| Corporate HQ/Facility | |
| Kentucky Facility | |
Nylene Canada
|
|
|---|---|
| Ontario Facility | |
| Canada Sales Office |
International
|
|
|---|---|
| South America | |
| China | |
| Malaysia | |
| Europe/Middle East |
