- Specialty Nylon Solutions
- Custom Engineered Thermoplastics
NYLENE USA
1421 Hwy 136 West
Henderson, Kentucky 42420
| Phone: | 270-826-7641 |
| Toll-free: | 800-626-7050 |
NYLENE CANADA ULC.
200 McNab Street
Arnprior, Ontario K7S 3P2
| Phone: | 613-623-3191 |
| Toll-free: | 800-267-7394 |
ISO/IEC 17025 & ISO 9001:2015 Accredited Facilities
Product is manufactured in Henderson, KY
Web: www.nylene.com | Email: info@nylene.com
TDS Ref ID: 1546
This information was updated on October 3, 2023
| Resin Type: |
|
| Description: |
|
| Properties | ASTM/ISO Procedure | Unit | English | SI | |
|---|---|---|---|---|---|
| Physical | |||||
| Specific Gravity | D792 | n/a | 1.11 | ||
| Moisture | D648 | % | <0.1 | ||
| Oxygen Permeability | D3985 | cc-mil/100 sq in-24 hr-atm* | (see note #2) | 3.8 | |
| Thermal | |||||
| Melt Point | D3418 | °F (°C) | 385 | 195 | |
| Film | |||||
| Break Stress | D882 | psi (MPa) | 84410 | 58 | |
| Maximum Strain | D882 | % | 350 | ||
| Youngs Modulus | D882 | psi (MPa) | 48575 | 335 | |
| Tensile Strength @ Yield | D882 | psi (MPa) | 3845 | 26.5 | |
| Yeild Stress | D882 | psi (MPa) | 3915 | 27 | |
| Ultimate Tensile Strength | D882 | psi (MPa) | 8645 | 60 | |
| Notes: |
|
|---|
| Zone | °F (C°) |
|---|---|
| Feed | 450-470 (232-243) |
| Transition | 470-490 (243-254) |
| Metering | 445-475 (229-246) |
| Die | 480-500 (249-260) |
| Melt Temp. | 480-500 (249-260) |
| Line Rate | pph-rpm |
|---|---|
| 21/2" extruder | 1.5-1.9 |
| 31/2" extruder | 3.5-4.5 |
| 41/2" extruder | 6.5-7.5 |
Residence Time: Screw should not be left idle for more than 3-4 minutes with melt in the barrel. Excess residence will be visible as black carbon specs in the melt.
Regrind Level: Typically, up to 25% is recommended but higher levels are possible with little or no effect on flow and finish.
Drying Temperature: Although Nylene resins are packaged and delivered in a low moisture state, it is good material handling practice to use a hopper dryer to maintain dryness. Should pre-drying be necessary, use settings of 65 °C (150°F) air at dew point of -40 at a rate of 1 cu. ft. / hour per pound of resin and a residence time of 2-4 hours.
Cooling and Sizing: While both air and water can be used as the cooling medium, air is preferred. The use of air allows additional time for sizing and reduces residual stress. This aids in reducing warpage, especially in profiles with varying wall sections. If water is used, heat the first section to above 38 °C 100°F) to reduce quenching and residual stress.
Die Design: Draw down of 30% is typical for all dimensions except wall thickness.
Fillers/Reinforcements:
Approvals & Recognition:
Automotive Colors:
Disclaimer
Nylene USA and Nylene Canada ULC are subsidiaries of the Polymeric Resources Corporation (PRC). Nylene companies develop and manufacture specialty nylons and engineering thermoplastics.
Nylene USA
|
|
|---|---|
| Corporate HQ/Facility | |
| Kentucky Facility | |
Nylene Canada
|
|
|---|---|
| Ontario Facility | |
| Canada Sales Office |
International
|
|
|---|---|
| South America | |
| China | |
| Malaysia | |
| Europe/Middle East |
